Selecting the right radio frequency filter depends on your specific reception goals and the environment in which you operate. Whether you are trying to block strong local broadcast signals or isolate specific satellite frequencies, the filter's attenuation and center frequency are critical factors.
This comparison examines seven distinct filter modules, ranging from simple bandstop filters for SDRs to complex LNA modules for satellite and ham radio use. Each option addresses a different frequency range and application, helping you match the hardware to your signal processing needs.
Our pick: Flamingo+ FM v2 Bandstop Filter. Ideal for users in urban areas with high-wattage FM transmitters who need high attenuation to prevent receiver overload.
Our 3 picks for different needs
Flamingo+ FM v2 Bandstop Filter
Ideal for users in urban areas with high-wattage FM transmitters who need high attenuation to prevent receiver overload.
Read the details
NooElec SAWbird+ IR LNA Module
Best for capturing L-Band signals from Iridium and Inmarsat satellites with its 1620MHz centered SAW filter and LNA.
Read the details
Nooelec Ham Filter Bank Barebones
Suitable for ham radio operators who need to switch between five different VHF and UHF bands using a single module.
Read the detailsAll products, in detail
Flamingo+ FM v2 Bandstop Filter
This high-attenuation bandstop filter is designed to block strong broadcast FM transmissions that can overload software-defined radios. It offers over 60dB typical average attenuation and over 70dB typical maximum attenuation, making it suitable for urban environments with high-wattage transmitters. The filter maintains low insertion loss outside the stop band and minimizes impact on the adjacent VHF airband.
It is designed and manufactured in North America with a two-year warranty.
- Blocks 88-108MHz frequencies with >60dB typical avg. attenuation
- Features <0.25dB avg. insertion loss outside the stop band
NooElec SAWbird+ IR LNA Module
A self-contained LNA module designed for capturing L-Band signals from Iridium and Inmarsat satellites. It uses two ultra-low-noise LNAs and a custom high-performance SAW filter centered at 1620MHz. The module supports three power options: bias tee, on-board microUSB, or DC barrel connector. It includes a free male SMA to male SMA adapter and a USB to DC barrel connector adapter for flexible integration with various SDR setups.
- Centered at 1620MHz for Iridium and Inmarsat applications
- Powered via bias tee, microUSB, or DC barrel connector
Nooelec SAWbird+ H1 LNA Module
This module is tailored for hydrogen line detection and 21cm band experimentation. It combines two ultra-low-noise LNAs with a custom SAW filter centered at 1420MHz. The device offers three power input methods: bias tee, on-board microUSB, or on-board female header. Manufactured in North America, it comes with a full two-year warranty and direct support from the manufacturer, ensuring reliability for specialized radio astronomy or amateur radio projects.
- 1420MHz center frequency for hydrogen line detection
- Includes 2-year warranty and North American manufacturing
hokojix 20m30m40mCW Low Pass Filter
A compact low pass filter designed for amateur radio operators and audio enthusiasts working with CW and PEP power levels. It supports frequencies of 7MHz, 10MHz, and 14MHz, helping to remove unwanted higher frequencies from the signal. The unit is rated for CW 15W and PEP 20W power, making it suitable for home studios or radio competitions.
Its small physical size allows for easy integration into various audio and radio setups without taking up significant space.
- Rated for CW 15W and PEP 20W power levels
- Compact dimensions of 85mm x 37.5mm without connectors
Flamingo+ AM v2 Bandstop Filter
A high-performance broadcast AM bandstop filter for SDR applications that blocks frequencies from 300kHz to 1900kHz. It provides approximately 70dB attenuation for broadcast AM while keeping out-of-band insertion losses minuscule. The filter is fully EMI shielded in a custom anodized aluminum enclosure and includes an RF-rated ESD diode for protection.
It can pass through DC bias-tee power up to 200mA, allowing it to remain in the signal chain for most HF applications.
- Blocks 300kHz to 1900kHz with approx. 70dB attenuation
- Features EMI shielding and RF-rated ESD diode protection
RTL-SDR Blog FM Block Filter
A dedicated block filter for the broadcast FM band between 88 and 108 MHz, offering over 50dB of attenuation. It is designed specifically for SDR and radio scanner users to prevent FM overload. The filter uses SMA female connectors and includes a free SMA male to male adapter.
Insertion loss is less than 0.5 dB between 0 and 1 GHz, making it a straightforward solution for those needing to remove strong local FM signals from their reception.
- Blocks 88-108 MHz with over 50dB attenuation
- Insertion loss less than 0.5 dB between 0-1 GHz
Nooelec Ham Filter Bank Barebones
A multiband radio module featuring five separate bandpass filters covering common ISM frequencies for ham radio. It includes filters for 2m, 1.25m, 70cm, 33cm, and 23cm bands, allowing users to explore a wide range of frequencies in a single unit. The device features a pushbutton switch to apply a 4.5V bias tee voltage to the input SMA, facilitating smooth integration with bias tee-powered devices.
It is suitable for selective signal processing and transceiver protection.
- Covers 2m, 1.25m, 70cm, 33cm, and 23cm ham bands
- Includes pushbutton switch for 4.5V bias tee voltage
Head-to-Head Comparisons
Flamingo+ FM v2 vs RTL-SDR Blog FM Block Filter
Both filters target the 88-108 MHz broadcast FM band, but they differ in attenuation levels and design intent. The Flamingo+ FM v2 offers higher attenuation, with over 60dB typical average and over 70dB typical maximum, making it better suited for urban environments with strong transmitters.
The RTL-SDR Blog filter provides over 50dB of attenuation, which is sufficient for many standard SDR applications. If you are in a high-interference area, the Flamingo+ FM v2 provides a stronger block, while the RTL-SDR Blog filter is a simpler solution for general use.
SAWbird+ IR vs SAWbird+ H1 LNA Modules
These two NooElec modules share a similar architecture with dual LNAs and SAW filters but target different frequencies. The SAWbird+ IR is centered at 1620 MHz for Iridium and Inmarsat satellite signals, while the SAWbird+ H1 is centered at 1420 MHz for hydrogen line detection.
Both offer three power input options, though the H1 uses a female header instead of a DC barrel connector. Choose the IR for satellite tracking and the H1 for 21cm band experimentation or radio astronomy projects.
Flamingo+ AM v2 vs hokojix Low Pass Filter
These filters serve different purposes in the HF spectrum. The Flamingo+ AM v2 is a bandstop filter that blocks the entire broadcast AM band from 300 kHz to 1900 kHz, useful for SDR users who want to ignore AM broadcasts. The hokojix filter is a low pass filter that allows frequencies up to 7, 10, or 14 MHz to pass while attenuating higher frequencies, suitable for CW and PEP power applications.
The Flamingo+ is for reception filtering, while the hokojix is for transmission or specific band isolation.
Buying Guide
Attenuation Levels and Environment
The strength of the unwanted signal determines the required attenuation. In urban areas with high-wattage transmitters, filters with over 60dB attenuation, like the Flamingo+ FM v2, are more effective at preventing receiver overload. In rural or low-interference areas, a filter with 50dB attenuation may be sufficient.
Assess your local RF environment to choose the appropriate level of blocking to avoid unnecessary signal loss in adjacent bands.
Frequency Range and Application
Identify the specific frequency band you need to filter. Bandstop filters block a specific range, such as the FM or AM bands, while low pass filters allow lower frequencies to pass. SAW filter modules are centered on specific frequencies for satellite or ham radio use.
Ensure the filter's center frequency or passband matches your intended application, whether it is for SDR reception, satellite tracking, or amateur radio communication.
Power and Connectivity Options
Check how the filter integrates with your existing equipment. Some modules, like the SAWbird series, offer multiple power options including bias tee, microUSB, and DC barrel connectors. Others, like the Flamingo+ AM, support DC pass-through for bias-tee powered devices. Ensure the connectors match your SDR or radio, and consider whether you need to power an LNA through the filter.
Compatibility with your setup is crucial for seamless operation.
Protection and Build Quality
Consider the physical protection offered by the filter. The Flamingo+ AM features EMI shielding and an RF-rated ESD diode to protect both the filter and the connected radio. Build quality and enclosure type can affect performance in noisy environments. For outdoor or high-power applications, a robust enclosure and proper shielding are important.
Check the warranty and manufacturer support to ensure long-term reliability of your investment.
Frequently Asked Questions
What is the difference between a bandstop and a low pass filter?
A bandstop filter blocks a specific range of frequencies while allowing others to pass, such as blocking the FM band. A low pass filter allows frequencies below a certain cutoff to pass and attenuates higher frequencies. Choose based on whether you need to remove a specific band or limit the upper frequency range.
Can I use these filters with any SDR?
Most of these filters use SMA connectors, which are common on many SDRs. However, you should verify that your SDR has SMA inputs and that the filter's power requirements match your setup. Some modules require bias tee power, while others can be powered via USB or DC.
Do I need to remove the filter when not in use?
For bandstop filters like the Flamingo+ AM, the manufacturer recommends removing it when not receiving HF frequencies to minimize any potential impact on other bands. For low pass filters, it may be fine to leave them in place if you are always working within the passband.
Check the specific product recommendations.
What is a SAW filter?
A SAW (Surface Acoustic Wave) filter is a type of filter that uses acoustic waves to filter signals. They are known for their high performance and sharp cutoffs. In these modules, SAW filters are used to isolate specific frequencies for satellite or ham radio applications, providing precise signal selection.
This article is part of our complete guide Electronics — browse all our comparisons and buying guides.
Last update on 2026-11-19 / Affiliate links / Images from Amazon Product Advertising API
